Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Cross Roads
Gate parts and welding in Cross Roads usually comes down to one of two jobs: a hinge post that has heaved out of plumb from Blackland Prairie clay, or a wide pipe-panel farm gate that has sagged until the latch will not catch. Hal Gatewood and our crew handle both, on site, with a welder in the truck and the parts to match what is already hanging on your posts. We serve the acreage properties, horse farms, and long-driveway homes throughout Cross Roads, and a live person answers when you call (940) 394-8744, any hour, any day.
Why Gatewood Fence & Gate Is Cross Roads’s Preferred Gate Parts & Welding Company
Hal Gatewood has been fixing gates since 2001, and his name is on the shop. That means when you call about a sagging swing gate on a Cross Roads horse property, the person who shows up works for him directly, not for a franchise three states away. Our Gate Parts & Welding crew has spent years working the rural driveways and farm entrances of Denton County, and we understand what this specific soil does to a hinge post. Cross Roads customers do not get a trainee with a clipboard. They get someone who knows that a gate sags in the hinge post, not in the middle, and that starts with checking plumb before touching the operator.
We answer the phone with a live person around the clock. Not a voicemail. Not a chatbot. When your gate will not close and your horses are standing at the opening, you need a human voice on the first ring. We also stand behind every repair with our 90-Day Done Right Promise, in writing. If it is not done right, one call brings us back. That is not a marketing line. That is how Hal has run this business for over two decades.
Our Gate Parts & Welding Services in Cross Roads
Post Replacement
In Cross Roads, the hinge post is usually the problem before anything else is. Blackland Prairie clay swells when wet and shrinks when dry, and over two or three seasons that cycle can migrate a corner post several inches out of true. We dig out the old footing, set a new post in concrete deep enough to resist the heave, and weld or bolt the hinges back so the gate hangs square. No amount of operator adjustment fixes a gate whose hinge post has tilted. The post has to be reset first.
Hinge Replacement
A heavy ranch gate on a Cross Roads acreage lot puts enormous load on its hinges, especially when livestock lean against it or horses rub on the rail. We replace worn or bent hinges with heavier-gauge steel and weld them in place rather than relying on bolts alone. On a recent job off Fishtrap Road, our crew found a hinge post that had leaned nearly four inches over two wet-dry cycles. We reset the post in a deeper concrete footing, welded a reinforced hinge bracket, and realigned the LiftMaster operator before checking the safety photocell. The gate now swings clean without binding.
Rail Repair
Pipe-panel perimeter fencing and ranch-style entry gates are standard equipment across Cross Roads, and the rails take the abuse. Livestock pressure, wind load, and the occasional ATV bump all work against the welds and joints. When a rail cracks or a cross-member pulls loose, we cut out the damaged section, fit a matching pipe or tube, and weld it back so the gate is straight and strong again. We weld on site, in your driveway, so your gate stays in Cross Roads instead of riding to a shop on a flatbed.
Custom Welding
Sometimes the part you need does not exist on a shelf anywhere. That is where a welder in the truck matters. We fabricate custom hinge brackets, latch plates, gate extensions, and bracing for Cross Roads properties that were built around a specific gate, not a catalog. Hal is a repair-first guy. If a bracket can be cut, bent, and welded stronger than a replacement, that is what we do. You pay for the actual problem, not a parts invoice.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Cross Roads
We stock parts and service operators from BFT, Linear, and Ghost Controls, along with six other major brands. If you have a solar-powered BFT on a shaded Cross Roads driveway or a Linear slide operator that has started grinding, we can pull the right part and install it the same visit. You are not waiting on a backorder from a distributor while your gate sits open. We keep the common wear items on the truck because in Cross Roads, a gate that will not close is a livestock escape waiting to happen.
Common Gate Parts & Welding Problems We See in Cross Roads Homes
- Hinge posts heaved out of plumb. The clay soil under Cross Roads expands and contracts with every wet-dry season, and a post set too shallow will lean within a couple of years. The gate then binds at the latch, strips the opener gears, and finally will not close at all.
- Solar operators failing on shaded driveways. Long, tree-lined entrances are beautiful, but a solar panel that only gets four hours of sun will not keep the battery up. Winter ice storms compound the problem, and the gate goes dead at the worst time.
- Wide farm gates sagging at the hinge side. Livestock push against the rails, the hinge post takes the load, and the latch end drops. The loop detector loses alignment with the gate and the operator thinks the gate is still open.
- Latches and locks that no longer line up. After years of heave and settle, the gate may still swing, but the latch post and the gate-side hardware are no longer on the same plane. That is a welding and alignment job, not a lock replacement.
Pricing for Gate Parts & Welding in Cross Roads, TX
On Cross Roads acreage properties, most gate parts and welding jobs fall into predictable ranges. A hinge replacement on a standard residential swing gate typically runs $180 to $340 per hinge, including the welded bracket. Post replacement, with the old footing removed and a new post set in poured concrete, runs $450 to $850 depending on depth and whether we are also realigning the operator. Rail repair and custom welding usually land between $150 and $500, and full gate realignment after clay heave runs $200 to $400. You will hear the price before we start, in writing, and it does not change at the door. Estimates are free, there is no trip charge inside the county, and we knock $40 off any repair over $200. Seniors and veterans get 10% off, permanently.
We Also Serve Cities Near Cross Roads
While this page focuses on Gate Parts & Welding in Cross Roads, we run the same trucks and the same crew into Denton, Argyle, Flower Mound, and Little Elm. If you are on the edge of Cross Roads and your driveway technically falls in a neighboring town, call anyway. Our service area follows the county roads, not the signposts.
Serving Cross Roads, TX - Our Local Coverage Area
We’re based in the Cross Roads area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Cross Roads
The Blackland Prairie clay under Cross Roads swells hard when saturated and shrinks hard in drought, and that cycle steadily pushes shallow-set posts out of plumb. Within two or three seasons a hinge post can lean several inches, and the gate will sag, bind, and eventually stop closing. The fix is resetting the post in a deeper concrete footing, which we do on site. Call (940) 394-8744 and we will check the plumb before we touch the operator.
Yes, and that is a standard job for us in Cross Roads. We cut out the failed section, fit matching pipe, weld it back, and reinforce the hinge bracket so the load is carried by the post, not the weld alone. If the hinge post has moved, we reset that first. Otherwise you will fix it twice.
The battery starves. A panel that only gets morning sun on a tree-lined Cross Roads driveway cannot keep the battery charged, and after a winter ice storm the opener goes dead. We fix this with a larger panel, a better mounting location, or a wired power run when practical. A live person answers around the clock at (940) 394-8744.
Usually one or both. Grinding on a slide gate in Cross Roads often means the rack has pulled away from the post or the rollers are shot, and continuing to run it chews up the gear. We inspect the weld points and the drive components in the same visit, and replace or repair only what is actually failing.
Yes. Every time we finish a weld, replace a post, or realign an operator on a Cross Roads property, we check the safety photocells, the reversing edge, and the force settings before we call the job done. A gate that cannot reverse when it meets resistance is a danger to kids, horses, and anyone on the driveway.
If your gate is sagging, grinding, or dead at the panel, call (940) 394-8744 for a free estimate. Hal Gatewood’s name is on the shop, his crew serves Cross Roads directly, and every job carries the 90-Day Done Right Promise in writing. We answer the phone with a live person, day or night.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Cross Roads and Denton County since 2001.