Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Installation in Cross Roads, TX: The Rural Acreage Problem Most Companies Miss
Most gate companies approach Cross Roads like it’s just another suburb. That’s a mistake. A driveway gate on a three-acre horse property off Fishtrap Road has nothing in common with a gate on a sixty-foot lot in Frisco. The span is wider, the operator works harder, and the ground underneath is working against you. If you’re searching for Gate Installation in Cross Roads, you need someone who understands Blackland Prairie clay, long runs without mains power, and gates built wide enough for a gooseneck trailer. Call us at (940) 394-8744 and you’ll get Hal or someone from his crew, not a recording.
Why Gatewood Fence & Gate Is Cross Roads’s Preferred Gate Installation Company
We’ve been doing Gate Repair in Cross Roads and hanging gates since 2001, and the name on the truck is the name on the shop: Hal Gatewood. When we drive out to Cross Roads, we’re not sending a crew from three counties away. Dispatch and scheduling run through our Dallas-Fort Worth office, but the people who show up know this area. They know Fishtrap Road, they know the horse properties around Cross Roads, and they know what happens to a gate post after two years of North Texas drought followed by a wet spring.
Our Gate Installation work in Cross Roads comes with a 90-Day Done Right Promise in writing. If something isn’t right, we come back and make it right. No runaround, no arguing with a call center. You call, a live person answers, and Hal shows up. We publish our address and license number. We answer the phone at 3 a.m. when an ice storm has your gate stuck halfway and a horse is out. That’s the job.
Customers here tend to be people who’ve already been burned once. They hired a national outfit that quoted one number on the phone and handed them a different invoice at the door. We don’t do that. The price is quoted and agreed before any work starts. Our senior and veteran discount is permanent, 10% on every job. Second opinion on a written estimate is free. No trip charge inside the county. And $40 off any repair over $200. These aren’t gimmicks. They’re standing offers, the same way Hal has run this shop for over two decades.
Our Gate Installation Services in Cross Roads
Most properties around Cross Roads need more than a standard gate hung on a post. They need a gate that works with the land, the livestock, and the distance from the house to the road. Here’s what we install most often out here.
Driveway Gate
A driveway gate in Cross Roads is usually the primary entry to a one-to-ten-acre property, not a decorative touch. We frame for the actual width your vehicles need. A gooseneck trailer is eight feet wide. A hay truck is wider. We measure for what you actually drive, not what fits in a suburban easement. Solid steel posts and Gate Parts & Welding in Cross Roads, done on site when the layout calls for it, plus an operator sized for the gate’s weight and swing cycle, not the cheapest one on the shelf.
Pedestrian Gate
Plenty of Cross Roads acreages have a separate walk gate beside the main drive, and it takes a beating. Kids, dogs, farriers, delivery drivers. We build pedestrian gates so they latch cleanly and don’t sag in the hinge. When the ground shifts, a pedestrian gate shows it first. We set the post deep and brace for the clay, because a gate that drags on the ground by August is a gate that was set for a different climate.
Sliding Gate
Sliding gates make sense on wide Cross Roads entrances where a swing gate would need too much clearance or fight the slope. Long runs, heavy frames, and operators that have to work every single day. We install slide gates with heavy V-track or cantilever setups depending on the lay of the land. A cantilever slide gate floats above the ground, which matters here. When the clay heaves, a track-mounted gate binds. A cantilever gate keeps rolling. That’s the difference between a gate installed for Cross Roads soil and one installed from a catalog.
Swing Gate
The swing gate is the workhorse of Denton County acreage, and it’s the one that suffers most from Blackland Prairie clay. A double swing gate on a farm entrance off a county road has two hinge posts and a center post. If any one of them leans, the leaves don’t meet, the latch doesn’t catch, and the opener strains. Before we mount an operator, we check plumb on every post. If a post has moved, we reset it in a deeper footing with extra concrete. Mounting a new operator on a leaning post just guarantees the new operator fails early.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Cross Roads
We’re certified to service nine major gate brands, and on Cross Roads installs we work with the ones that handle rural duty cycles well: Ghost Controls, Elite, DoorKing, and Mighty Mule among them. The right operator for a hobby farm on a county road is not the same as the right one for a gated community. We keep common parts stocked for these brands so we’re not waiting a week on a control board when your gate is stuck open at 7 p.m.
Common Gate Installation Problems We See in Cross Roads Homes
Here’s what we find over and over on Cross Roads properties. If any of this sounds familiar, the fix usually starts with the post, not the operator.
- Posts leaning from clay heave. Blackland Prairie clay swells when it’s wet and shrinks hard in drought. A corner post can move several inches off plumb in two or three seasons. No operator adjustment fixes a tilted hinge post. The post has to come out and be reset.
- Operators faulting on wide gates. A double swing gate on a ten-acre property weighs hundreds of pounds. Undersized operators burn out or error out constantly. We size the operator for the actual gate weight and swing arc, including wind load on a solid panel gate across open pasture.
- Solar panels losing charge under tree canopy. Long Cross Roads driveways often have mature oaks or cedar elms near the road. A solar gate opener installed without accounting for afternoon shade will leave your slide gate dead after a few cloudy days. We angle panels for winter sun and clear line-of-sight.
- Photo-eyes and keypads freezing in ice storms. The February 2021 freeze is the one everyone remembers, but it happens in smaller doses every few winters. Exposed rural driveways with no windbreak will freeze photo-eye lenses and keypad membranes, leaving the gate stuck mid-cycle. We seal and shield electronics for exposed locations.
Pricing for Gate Installation in Cross Roads, TX
Here’s what Cross Roads homeowners can expect to pay, based on the work we’ve done along Fishtrap Road, Hames Road, and the acreage tracts east of town.
| Service | Typical Range in Cross Roads |
|---|---|
| Single swing gate with operator (standard 12-14 ft) | $2,800 - $4,500 |
| Double swing gate with heavy-duty operator (16-20 ft ranch entrance) | $4,200 - $7,800 |
| Sliding gate (cantilever, 14-18 ft) | $3,500 - $6,500 |
| Pedestrian gate with welded steel frame | $600 - $1,400 |
| Solar power kit for gate operator (no mains at road) | $400 - $900 add-on |
| Post reset / re-plumb (each post, including concrete and labor) | $350 - $700 |
These are installed prices including labor, hardware, and the operator. A free measure and written quote is the only way to nail your exact number, because no two Cross Roads driveways are the same. What we can promise: the price we quote is the price you pay, and it’s agreed before we touch a tool. We don’t charge a trip fee inside the county. Call (940) 394-8744 for a free estimate.
We Also Serve Cities Near Cross Roads
Our crews work throughout Denton County and the surrounding area. In addition to Gate Installation in Cross Roads, we regularly handle installations in Denton, Argyle, Flower Mound, and Little Elm. Same team, same 90-Day Done Right Promise, same live person on the phone.
Serving Cross Roads, TX - Our Local Coverage Area
We’re based here and handle Cross Roads Gate Access Control, and we know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Cross Roads
Cross Roads sits on Blackland Prairie expansive clay, which swells dramatically when saturated and shrinks hard in drought. That repeated cycle physically moves post footings over time. Frisco and Prosper are largely built on concrete-slab subdivisions with engineered drainage and compacted fill, which keeps posts far more stable. A post on raw Cross Roads clay with a shallow footing can move several inches off plumb within two or three seasons, and the only real fix is to reset it deeper with more concrete. Call (940) 394-8744 and we’ll check plumb before we quote the operator.
Yes. We install solar-powered gate operators regularly on Cross Roads acreages where running mains power to the entrance would cost thousands. The key is sizing the solar panel and battery bank for the actual gate weight, daily cycle count, and shade conditions. On a five-acre property off Fishtrap Road, our crew installed a Viking swing gate operator with a solar kit after resetting a hinge post the clay had pulled out of plumb. The gate opens for horse trailers and daily keypad entry without mains power. Call (940) 394-8744 for a site assessment. Estimates are free.
Not strictly, but we recommend one for any Cross Roads ranch gate that opens for a vehicle leaving the property multiple times a day. A loop detector buried in the drive senses your truck or trailer and triggers the gate automatically, so you don’t have to key in every time you pull up. On rural acreages without a loop, a gate that only opens by keypad gets left open by everyone in a hurry. A loop keeps it closed when you’re not there and opens it when you roll up. Call (940) 394-8744 and we’ll tell you if your gate is a good loop candidate.
We set the hinge post in a footing deep enough to get below the most active clay movement, and we brace the gate frame so the load transfers to the hinge side properly. A pipe-framed gate sags in the hinge post, not in the middle, and that’s where we start. If the post has already leaned, we reset it before touching the gate. A sagging gate will always return unless the post is plumb and the footing is sized for the gate’s weight. Call (940) 394-8744 for a free estimate on a post reset or full gate install.
Yes. Automatic gate operators installed in Texas must comply with safety entrapment standards, which include photo-eye sensors that reverse a closing gate if anything crosses the beam. This is not optional, and we install them on every automatic gate we set. On exposed Cross Roads driveways, the photo-eyes need to be sealed and shielded against ice and wind-driven rain, or they’ll fault in winter weather. We set them so they work and stay working. Call (940) 394-8744 with questions about your existing setup. Second opinions on written estimates are free.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Cross Roads and surrounding Denton County since 2001.