Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for Denton Homeowners
A gate that hangs crooked or won’t close right isn’t just a hassle. It’s the first thing anyone notices about your property, and a weak point anyone can walk through. We install driveway gates, pedestrian gates, and security gates across Denton the way they should have been built in the first place: posts set deep enough to hold the weight, hinges that line up true, and motors paired to the actual load. Hal Gatewood has done this work since 2001, with his name on the shop and his crew doing the work. Call (940) 394-8744 and you’ll get a live person, not a recording.
Before you read further, know this: every gate we install in Denton carries our 90-Day Done Right Promise in writing. If something isn’t right, one call brings us back. That’s the whole point of hiring a local shop whose address you can drive past.
What Our Gate Installation Service Includes
Gate installation in Denton covers a lot of ground, from a single pedestrian gate at the side yard to a full double driveway gate with automation. Here’s what we do under each type, and when each one makes sense for your property.
Driveway Gate
A driveway gate is the one you open every day, sometimes six times a day. It takes the most abuse, so the post depth and hinge alignment have to be right from day one. We set posts in concrete below the frost line, hang the gate, and if it’s automated, pair the motor to the actual weight and swing of the panel. Most driveway gates we install in Denton are done in a day or two once materials are on site.
Pedestrian Gate
A pedestrian gate is the walk-through gate beside the driveway or along a fence line. It’s small, but it gets used harder than anything else on the property. We build these with the same post depth and hinge quality as a driveway gate, because a sagging walk gate is the most common repair call we get. If you’re tired of lifting the gate to latch it, that’s a hinge post problem, and we fix it at the root.
Sliding Gate
A sliding gate runs on a track instead of swinging, which makes it the right choice for short driveways or steep slopes where a swing gate won’t clear. The track, the rollers, and the motor all have to line up square, or the gate will bind and burn out the opener. We install cantilever and track-style sliding gates and adjust them so they roll smooth from the first pass. Sliding gates also work well when you need to close off a wide driveway without a center post.
Swing Gate
A swing gate is what most people picture: one or two panels that pivot on hinges at the posts. The hinges carry the entire weight, so we spec them by panel weight, not by guess. We see a lot of swing gates in Denton where somebody used light residential hinges on a heavy steel panel, and the gate sags within a year. We weld and bolt hinges sized for the actual load, and we set the posts deep enough that they won’t lean.
Double Gate
A double gate is two panels that meet in the middle, usually across a wide driveway. The trick is getting both panels to close in the right order and meet without a gap or a bind. We adjust the closing sequence, the stop, and the latch so both sides land where they should every time. If you’re automating a double gate, we make sure the motor is matched to the combined weight of both panels, not one.
Security Gate
A security gate is a gate built to actually keep somebody out, not just mark the property line. That means a heavier frame, heavier hinges, a lock that can’t be reached through the gap, and an opener with a manual release that actually releases under load. We build security gates in Denton with the same materials and attention we’d use on our own shop. And we show you how the manual release works before we leave, because a security gate that traps you outside your own driveway during a power outage isn’t security, it’s a hostage situation.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We install and automate gates with openers from Ghost Controls, DoorKing, Elite, and Mighty Mule, among others. Our experience with Ghost Controls goes back to their early residential swing kits, and we stock the mounting hardware and receiver parts for their current lineup. If you already have a Ghost Controls opener and need a new gate hung to it, we’ll match the arm geometry and travel limits to the new panel.
DoorKing is what we recommend most often for heavier driveway gates and light commercial applications in Denton. Their operators are built for duty cycles that would cook a residential opener, which matters when your gate cycles twenty times a day. We also work regularly with Mighty Mule, which is a solid choice for a homeowner who wants a dependable opener without spending DoorKing money. If you already own a gate opener from any brand, we’ll install the gate to match it, and we’ll be honest if the opener isn’t worth hanging on a new panel. Hal has been servicing gate motors since 2001, and he’ll tell you straight whether to keep the one you have or put the money into one that’ll last.
Signs You Need Gate Installation Right Now
- The gate drags or scrapes at the latch edge. That means the hinge post has moved or the hinges themselves are worn. Shimming it just moves the problem around. If the post has shifted, a new gate on the old post won’t fix it.
- You have to lift the gate to open or close it. When you lift a sagging gate, the stress goes straight into the hinges and the hinge post. Eventually the welds crack or the post snaps at the base. By the time you’re lifting it, the gate has already told you the post is failing.
- The gate bangs when it closes or bounces back open. That’s a sign the closer or the opener’s limit settings are wrong, or that the gate frame has twisted. Continuing to use it burns out the motor and breaks the latch.
- The gate has a gap at the bottom on one side but not the other. That’s a hinge post leaning, full stop. A gate sags in the hinge post, not in the middle, and that’s where we start every installation and every repair.
- You’re replacing your fence and the old gate looks tired next to it. Nobody wants a brand new fence with a gate that’s twenty years old and faded to a different color. If the fence crew is quoting you a gate anyway, get the gate done by someone who hangs and welds gates for a living, not someone who does it three times a year.
Our Gate Installation Process - Step by Step
1. You call, a live person answers
The phone at Gatewood Fence & Gate is answered by a person, 24 hours a day. You explain what you need, we ask about the property, the driveway layout, and whether there’s an existing gate or opener. We’ll schedule a look at your site, and there’s no trip charge if you’re inside the county.
2. We measure and lay eyes on the site
Hal or one of his crew comes out, measures the opening, checks the ground, and looks at what’s already there. If there’s an old gate post, we check whether it’s sound enough to reuse. A lot of quotes in this business get written over the phone without a human ever putting a tape on the opening, and that’s how you get a surprise when the gate doesn’t fit.
3. You get a written quote with the real number
The price we quote is the price you pay, and it includes the gate, the posts, the concrete, the hinges, the labor, and anything else specific to your job. No vague “installation fee” line that doubles later. We also offer a free second opinion on any written estimate from another company, because we’d rather you compare us honestly than assume we’re all the same.
4. We build and hang it right
If the gate is steel, we weld it to fit your opening and the hardware we spec’d. If it’s a pre-fabricated panel, we verify the frame is square before we hang it. Posts are set in concrete below the frost line, and the gate is hung and adjusted on site. If you asked for automation, the opener is paired to the actual panel weight and travel, not a preset guess.
5. We walk you through it and stand behind it
Before we leave, we demonstrate the gate, show you the manual release if it’s motorized, and make sure you know how it should sound and feel. Every job includes our 90-Day Done Right Promise in writing. If something isn’t right, one call brings us back, no runaround.
If you’d rather see the kind of work we do before you call, drive by the shop. The name is on the building, and the address is published, which is more than you can say for half the people hanging gates in Denton.
How Much Does Gate Installation Cost in Denton?
A typical pedestrian gate installation in Denton runs $400 to $900, and you can see more on gate installation pricing below, depending on the width, the material, and whether we’re reusing a sound post or setting new ones. A single driveway swing gate in steel usually lands between $1,800 and $4,500, and a double driveway gate runs $3,500 to $9,000 when you factor in the automation. Sliding gates typically run $2,500 to $6,500 for the track, the gate, and the motor. The biggest variables are the panel weight, the post spacing, the opener you choose, and whether there’s power at the opening already.
Here’s what moves the price in Denton:
- Existing posts: If the current posts are set deep and still plumb, we can often reuse them. That saves concrete, time, and a good chunk of the total.
- Automation: A manual gate is less expensive up front, but adding a motor later means running power and rebalancing the panel. If you think you’ll automate within a couple years, it’s cheaper to do it now.
- Panel material and weight: Heavier gates need heavier hinges, stronger posts, and a bigger opener. Those all cost more, but they’re what keep the gate from sagging in two years.
- Electrical run: If there’s no outlet at the opening, the price includes running power, and that depends on how far the panel is from the house. Solar is an option for some openers, and we’ll tell you honestly whether it’s going to work for your site or just look good on a brochure.
Every estimate is free and in writing before any work starts. We also offer $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. If you already have a written estimate from someone else, bring it in and we’ll give you a free second opinion on it.
Gate Installation Near Denton - Our Service Area
We install gates all across Denton and the surrounding towns: Argyle, Flower Mound, Little Elm, Krum, Corinth, Shady Shores, Cross Roads, Copper Canyon, Lantana, Bartonville, and Lake Dallas. If you’re in one of those areas, you’re not far from us, and you’re still getting the same homegrown service. If you’re outside Denton proper, the first thing to check is whether you’re inside the county, because that decides whether the trip charge applies. For Gate Installation in Argyle, we can usually be there the same week. For Gate Installation in Flower Mound, the drive is short and we know the neighborhoods. And for the full rundown on Gate Installation in Denton, that page has what you need.
Serving Denton, TX - Our Local Coverage Area
We’re based in the Denton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in Denton
Gate installation is the process of setting the posts, hanging the gate panel or panels, and optionally adding an opener and access control so you can open and close it without getting out of the car. It’s more than just bolting a gate to a post: the posts have to be deep enough and plumb enough to hold the weight for years, and the opener has to match the load. We handle the whole job, from the first measurement to the final walkthrough, and we weld on site when needed.
Most single driveway gates in Denton are installed in one day once materials are on hand. A double gate with automation may take two days, and a custom welded steel gate takes a little longer because of the time at the shop. We’ll give you a real timeline in the written quote, and if weather or materials delay anything, we’ll tell you before it becomes your problem.
You’ll usually pay between $1,800 and $9,000 for a driveway gate with automation, depending on whether it’s a single or double, what opener you choose, and whether we’re running power. A pedestrian gate is less, and a custom welded security gate can run more. The exact number depends on your opening, so call (940) 394-8744 and we’ll come measure it and give you a free written estimate.
Yes. DoorKing is one of the brands we install most often on new driveway and security gates in Denton. We match the operator to the actual weight and cycle count of the gate, not a generic chart, and we test the full cycle before we leave. If you already have a DoorKing that you want to keep, we’ll tell you honestly whether it’s sized right for the new gate.
A live person answers our phone 24 hours a day, 7 days a week, and if your gate is stuck open or off its track and your property is exposed, we’ll tell you what it’ll take to get it closed. Not every job is a same-day job, but we don’t make you wait through a phone tree to find out. Call (940) 394-8744 and you’ll talk to a person who can actually help.
Every installation carries our 90-Day Done Right Promise, in writing, on the job. If something isn’t done right, one call brings us back to make it right, no runaround. The promise covers the workmanship on the gate and the hardware we installed, and we’ll tell you at the time of the estimate what the manufacturer’s warranty on the opener covers.
You don’t need to do much. Clear the area around the opening so we can get a tape and a level on it, and make sure we can access both sides of the gate. If you have a dog, keep it inside or in a separate part of the yard while we’re working. We’ll handle the digging, the concrete, the wiring, and the cleanup, and we’ll show you the finished gate before we leave.
Schedule Your Gate Installation Service in Denton Today
If you’re ready to stop fighting a sagging gate or just want a straight answer on what a new one will cost, call (940) 394-8744. A live person answers, we’ll schedule a time to measure, and you’ll get a written quote with no trip charge inside the county. Hal Gatewood has been building and fixing gates in Denton since 2001, and his name is on every job. The estimate is free, the price won’t change at the door, and the gate will be done right.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Denton since 2001.