Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Lantana
Gate parts and welding in Lantana typically runs $150 to $650 for most hinge, post, and rail repairs, with custom welding jobs priced after we see the gate. That’s the honest range, and we’ll put it in writing before any torch gets lit. If your gate is sagging, binding, or dragging across the driveway in Lantana, call (940) 394-8744 and you’ll get Hal Gatewood or someone from his crew on the line, not a recording. We’ve been doing this work since 2001, and the black clay under Lantana keeps us busy year-round.
The thing about Lantana is that it looks pristine from the street, but underneath every ornamental iron gate is a footing that’s been fighting Denton County soil since the day it was poured. That fight shows up as a hinge post leaning two degrees out of plumb, a slide gate that grinds to a halt, or an opener that faults out every spring after the rains. We bring the welding rig to your driveway, fix it on site, and stand behind the work with our 90-Day Done Right Promise in writing. Our full Gate Parts & Welding team knows exactly what Lantana gates are up against.
Why Gatewood Fence & Gate Is Lantana’s Preferred Gate Parts & Welding Company
Hal Gatewood’s name is on the shop door and on every invoice. He’s been at this since 2001, and when you call about a gate problem in Lantana, you’re talking to someone who has driven those streets, looked at those HOA requirements, and welded hundreds of ornamental iron gates in this exact soil condition. We don’t hide behind a dispatch queue or a call center in another state. The phone rings, a person answers, and that person knows gates.
Lantana customers call us because the work gets done once and it holds. Our 90-Day Done Right Promise isn’t a marketing line, it’s stamped on every job we write up. If something we touched isn’t right within 90 days, Hal comes back and makes it right. No runaround, no argument about whether it’s covered. That’s the kind of accountability that matters when you live in an HOA-governed community where a broken gate can draw a letter from the Architectural Review Board.
We also show up prepared. A service call to Lantana means checking the gate’s posts, hinges, operator limits, and safety sensors in one visit, because we know they fail together out here. The person who shows up is background-checked, uniformed, and carrying the sensor realignment tools every Lantana post repair actually needs. We don’t send a helper with a socket set and hope for the best.
Our Gate Parts & Welding Services in Lantana
Hinge Replacement
Hinge replacement in Lantana usually means the gate was hung on builder-grade hardware that was never meant for daily automated cycles. We cut off the old hinge, weld in a new barrel or strap hinge rated for the gate’s weight, and shim the leaf so the gate swings true. Prices for hinge replacement in Lantana run $120 to $400 depending on how many hinges and whether the post itself has moved. If the post moved, replacing hinges alone is wasted money, and we’ll tell you that before we start.
Post Replacement
This is the big one in Lantana. Denton County’s expansive black clay swells in the spring and shrinks in the summer, and every cycle works gate posts a little further out of plumb. When we replace a post, we don’t just pull the old one and pour the same shallow footing that failed. We dig deeper, add steel reinforcement, and set the new post in concrete mixed for expansive soil. Post replacement in Lantana typically runs $400 to $900 per post, including removal, new footing, welding, and re-hanging the gate. On automated gates, expect a sensor recalibration in the same visit.
Rail Repair
Ornamental iron gates in Lantana take a beating on the bottom rail, especially swing gates that drag when a post settles. We weld in replacement rail sections, patch rusted-through pickets, and reinforce corners where the builder’s original welds were thin. Rail repair runs $150 to $400 depending on how much steel needs replacing. Most Lantana rail repairs are a same-day job when we have the material profile in the truck, which we usually do.
Custom Welding
Sometimes the gate you want doesn’t exist in a catalog. Custom welding for Lantana gates covers everything from fabricating a matching ornamental picket to building a full replacement leaf that matches your HOA’s approved iron style. We weld on site so your gate never leaves the property, and we can match the finish on 2000s-era Lantana gates that weren’t built to any standard profile. Custom welding is quoted per project after Hal sees the gate in person, but most Lantana custom jobs fall between $300 and $1,200.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Lantana
We’re certified to service nine major gate brands, and in Lantana we see a lot of LiftMaster, Ghost Controls, and Viking operators on builder-installed gates. Those builder-grade units fail under daily automated cycles, often because the limit switches and loop detectors were never tuned for Lantana’s shifting post conditions. When we service a BFT or Linear operator in Lantana, we calibrate it for the actual soil movement your gate experiences, not the factory default. We carry common parts for these brands in the truck, which means fewer follow-up trips and faster repairs for Lantana homeowners.
Common Gate Parts & Welding Problems We See in Lantana Homes
- Expansive clay heaving the hinge post. Lantana sits on Denton County black clay that swells dramatically after spring rain and shrinks in summer drought. The hinge post moves, the gate sags, and the latch stops lining up. Fix the panel without the post and you’ll fix it twice.
- Builder-grade operators failing under daily cycles. A lot of Lantana gates were built with the cheapest operator the builder could spec. The unit burns out, strips its drive gear, or faults on the close-limit. We replace it with something rated for the gate’s actual weight and cycle count.
- Manual gates retrofitted with automation but no conduit. We see this often in Lantana’s newer sections. The homeowner adds a keypad or solar gate opener after closing, but there’s no power run to the gate. We trench and run conduit, install the operator, and wire safety edges so it passes inspection.
- Rack and pinion slide gates binding on heaving track posts. When the clay pushes the track supports up even half an inch, the rack strips the pinion gear or the gate trips its entrapment protection. We repair the rack, shim or replace the track posts, and realign the drive so it rolls clean again.
Pricing for Gate Parts & Welding in Lantana, TX
Here’s what you can expect to pay for gate parts and welding work in Lantana, based on jobs we’ve done in this community over the past several years: hinge replacement runs $120 to $400, rail repair runs $150 to $400, post replacement runs $400 to $900 per post, and custom welding runs $300 to $1,200 for most residential projects. What moves the price is the size of the gate, how far the post has shifted, and whether the opener needs recalibration after the structural work is done. We quote every Lantana job upfront, in writing, before any work starts. You’ll never get a phone quote and then a bigger number at the door. We also knock $40 off any repair over $200, charge no trip fee inside the county, and give a permanent 10% discount to seniors and veterans.
We Also Serve Cities Near Lantana
Our shop serves Lantana and the surrounding communities, including Denton, Argyle, Flower Mound, and Little Elm. If you’re in one of those areas and your gate is fighting the same black clay we see everywhere in this county, call (940) 394-8744. We’ll give you the same upfront price and the same 90-Day Done Right Promise.
Serving Lantana, TX - Our Local Coverage Area
We’re based in the Lantana area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Lantana
Yes, in most cases. Lantana’s Community Association has an Architectural Review Board that governs exterior modifications, including gate replacement, finish changes, and sometimes even major hardware swaps. If you’re matching the existing style and finish, the process is usually straightforward, but you’ll want written approval before steel gets cut. We’ve worked with this HOA’s requirements for years and can help you document the scope of work so the review goes smoothly. Call (940) 394-8744 and we’ll walk you through what the board typically asks for on gate repairs and welding.
Fix the hinge post first. A gate sags in the hinge post, not in the middle, and that is where we start. If your Lantana gate is dragging or the latch won’t line up, the post has shifted in the clay, and welding the panel or adjusting the hinges without resetting the post is a temporary patch. We re-plumb the post, re-hang the gate, and then recalibrate the opener so it’s not fighting a misaligned gate. Call (940) 394-8744 for a free estimate on fixing it right.
Because the Denton County clay swells after spring rains and shifts your gate posts enough to knock the close-limit sensor and safety photocell out of alignment. The opener isn’t broken, it’s confused. In the Bandera subdivision, we reset a hinge post on an ornamental swing gate that had tilted after spring rains, then had to recalibrate the LiftMaster operator’s close-limit and safety photocell before the gate would close reliably. The builder-grade post footing had no rebar cage, so we poured a deeper footing with steel and welded new hinge pins to eliminate the recurring sag. That’s the fix that lasts. Call (940) 394-8744 and we’ll bring the sensor tools on the first trip.
Yes, but most Lantana homes with manual gates don’t have conduit or a power run to the gate location, which means we need to trench and run electrical before the operator goes in. We handle the full job: conduit, wiring, operator, safety edges, keypad, and programming. We’ll also check the hinge post before we mount anything, because automating a gate on a shifting post just makes the fault codes happen faster. Call (940) 394-8744 for a free measure and a written price.
The rack and pinion gear set wears first, typically because the track support posts have heaved in the clay and the gate is no longer rolling level. That misalignment strips the drive gear and can trip the entrapment fault, which shuts the gate down entirely. We replace the rack section, weld the track posts back to level or set new ones, and realign the pinion so the gate rolls without grinding. Slide gate track and rack repair in Lantana usually runs $300 to $700 depending on how much of the run needs work. Call (940) 394-8744 and we’ll give you an exact number before any work starts.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Lantana since 2001.