Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Bartonville
Gate motor and opener repair in Bartonville usually runs between $240 and $650, and most jobs are done the same day we come out. If your driveway gate is dragging, grinding, or dead after a storm, call (940) 394-8744 and Hal will answer. We’ve worked on enough custom gates along McMakin Road, Jeter Road, and the estate properties off of FM 407 to know that Bartonville gate systems are different from what you’ll find ten minutes south.
Bartonville isn’t a subdivision town. It’s large acreage, custom homes, horse operations, and gates that weigh more than some cars. That changes how a motor gets serviced. A generic opener swap that works fine on a cookie-cutter lot in Flower Mound will fail early on a Bartonville estate if the post has moved and nobody reset it. We work on the gate in your driveway, on our own schedule, and we don’t leave until the thing runs like it should.
Why Gatewood Fence & Gate Is Bartonville’s Preferred Gate Motor & Opener Company
Hal Gatewood started this shop in 2001, and his name has been on it ever since. The owner shows up. That matters in Bartonville, where half our customers have already watched a national chain send a different tech in a different truck three visits in a row. Around here, a gate company lives or dies by word of mouth across the equestrian set, and we’ve built our reputation the slow way: one repaired gate at a time, one neighbor telling another neighbor.
We answer the phone with a live person, 24 hours a day. Not a voicemail, not a dispatch queue. Hal or a member of his crew picks up. If you’ve got a gate that won’t open and a trailer full of horses stuck at the end of the driveway, that phone call is the difference between a minor annoyance and a real problem. Response time to Bartonville is typically under two hours for emergencies, and same-day service is the norm, not the exception.
Every job carries the 90-Day Done Right Promise, and that promise is in writing. If something isn’t right, one call brings Hal back. That’s not a warranty buried in fine print. It’s his name on the invoice, and he means it.
Our Gate Motor & Opener Services in Bartonville
We’ve serviced enough Bartonville properties to know exactly where each gate type tends to fail. Here’s how we handle the most common calls west of Denton.
Motor Installation
A new gate motor in Bartonville typically runs $750 to $1,800 installed, depending on gate weight, swing versus slide, and whether we’re running new conduit or working with existing wiring. Custom wrought iron driveway gates common off McMakin Road often need higher-torque operators than a standard suburban gate. Hal won’t sell you a motor rated for 600 pounds and bolt it onto a 1,400-pound gate. He sizes the motor to the actual load, because in Bartonville the gate is usually heavier than the spec sheet assumes.
Motor Repair
Most Bartonville motor repairs run $240 to $650. That includes bad capacitors, failed circuit boards, stripped limit switches, and geartrain wear on older LiftMaster and Linear operators. We repair before we replace. If a $30 capacitor fixes the problem, that’s what you pay for. If the motor is genuinely shot, we’ll show you the dead part and quote the replacement before any work starts. No invoice surprises at the end of the day.
Linear Motor
Linear actuators are common on Bartonville estate gates, especially on heavy swing gates with ornamental iron. When a Linear motor fails, it’s usually the brushes or the limit switch assembly, not the entire unit. We stock replacement Linear components and can source anything else within a day or two through our Dallas-Fort Worth parts network. A typical Linear motor rebuild in Bartonville runs $320 to $550, and we warranty our work through the 90-Day Done Right Promise.
Slide Motor
Slide gates are the workhorses of Bartonville ranches and equestrian properties. They’re usually on the pasture side of the property, opening and closing twenty times a day during feeding season. A slide motor replacement in Bartonville runs $700 to $1,500 depending on the gate weight and whether we need to rebuild the roller track. When clay soil shifts under the track, the gate binds, and the motor burns out trying to push it. We fix the gate alignment first, then address the motor. Fixing the motor without fixing the track is how you buy a second motor in eighteen months.
Battery Backup
Battery backup systems in Bartonville run $400 to $900 installed. After Winter Storm Uri in February 2021, we saw a wave of failed circuit boards and dead backup batteries across Denton County. Most of those systems had been installed years earlier, never load-tested, and never expected to actually carry a gate through a three-day power outage. We now test backup batteries under actual motor load during every installation and every annual service call. If your gate can’t open on battery power, we find out before the next freeze does.
Intercom Integration
Bartonville estates frequently have gate intercoms and cameras that were installed by three different companies over three different decades. When you upgrade the motor, the intercom and the camera should all talk to each other. We integrate existing systems with new operators, including Ghost Controls, Viking, and BFT hardware. Intercom integration in Bartonville typically runs $200 to $500 on top of the motor work, depending on wiring condition and whether we’re retrofitting an older analog system.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Bartonville
We service and install the brands Bartonville estates actually use: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That’s nine major manufacturers, and we carry common parts for most of them in the truck. When a property needs something specific, like a BFT control board or a Viking loop detector, we can usually have it in hand within 24 to 48 hours through our local parts network. No waiting two weeks for a component that should’ve been on the shelf.
Common Gate Motor & Opener Problems We See in Bartonville Homes
- Seasonal binding from expansive clay soil. Denton County’s Blackland Prairie clay shrinks during dry summers and swells during wet winters. Hinge posts shift out of plumb, and cantilever slide gates start dragging or binding. You didn’t install it wrong. The ground moved under it. We reset posts and realign tracks, and the gate runs clean again.
- Dead battery backups that weren’t load-tested after Uri. The February 2021 storm killed a lot of circuit boards and exposed battery systems that were only good for a couple of open-close cycles. If your backup hasn’t been tested since then, it probably isn’t doing what you think it is.
- Custom ornamental gates with bespoke component problems. A $10,000 wrought iron driveway gate often has non-standard hinge geometry, custom limit switch placements, and operator mounts that don’t match any current template. A simple motor swap can turn into a two-week parts hunt without a shop that knows how to source custom components.
- Dual-gate properties where both gates fail at once. On many Bartonville estates, the decorative front gate and the pasture gate share the same driveway loop. One shifting post can bind both gates simultaneously, and you need a technician who can reset a high-end ornamental operator and a utilitarian ranch slide motor in the same visit.
Pricing for Gate Motor & Opener in Bartonville, TX
Gate motor and opener work in Bartonville falls into fairly predictable ranges. Repairs run $240 to $650 for the bulk of what we see: capacitors, control boards, limit switches, and actuator brushes. New installations run $750 to $1,800 depending on gate weight and wiring condition. Slide motor replacement on a heavy ranch gate tends to run $700 to $1,500. Battery backup systems run $400 to $900 installed and tested under load. These are honest numbers for this market, not lowball figures designed to change at the door.
The price Hal quotes is the price you pay. Every quote is in writing, agreed before any work begins, and backed by the 90-Day Done Right Promise. Standing offers apply in Bartonville: $40 off any repair over $200, no trip charge inside the county, free second opinions on any written estimate, and a permanent 10% discount for seniors and veterans. Call (940) 394-8744 for a free estimate on any gate motor or opener work.
We Also Serve Cities Near Bartonville
While this page is written for Bartonville, our Gate Motor & Opener team regularly works in Bartonville and the surrounding towns. We take calls from Denton, Argyle, Flower Mound, and Little Elm. If you’re in one of those areas with a gate that’s binding, grinding, or dead, the same live-person answer and the same 90-Day Done Right Promise applies.
Serving Bartonville, TX - Our Local Coverage Area
We’re based in the Bartonville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Bartonville
Your gate is installed correctly. The ground under it is moving. Bartonville sits on Blackland Prairie clay, which swells dramatically in wet winters and shrinks in dry summers. That heave pushes hinge posts out of plumb and throws cantilever slide gates out of alignment. The motor then fights the gate weight instead of moving it smoothly. The fix is resetting the post footing and realigning the track, not replacing the motor. Call (940) 394-8744 and Hal will take a look.
No. And you probably don’t want two companies, because on many Bartonville properties both gates share the same driveway loop, and one shifting post can bind both at the same time. We work on high-end ornamental swing gates and utilitarian ranch slide gates on the same visit. On a recent call off McMakin Road, we reset a $10,000 ornamental gate’s hinge post, realigned the rack and pinion, then walked the shared loop to the pasture gate and fixed that too. One trip, both gates running.
Test it under load, the way it would actually run during an outage. Most battery backups installed before February 2021 were never tested against a real multi-day power loss. We load-test backup batteries during every installation and every service call in Bartonville. If the battery only cycles the gate once when it should cycle ten times, we’ll tell you before the temperature drops. A replacement backup system runs $400 to $900 installed.
You can almost always keep the intercom and camera system you already have. We integrate existing hardware with new operators, including BFT, Viking, and Ghost Controls. The exception is very old analog intercoms that can’t talk to modern operator control boards without a retrofit. We’ll tell you the truth on that before any work starts. Integration work in Bartonville typically runs $200 to $500.
It means the problem is almost never the gate panel itself. A custom wrought iron gate that sags is usually sitting on a hinge post that’s tipped out of plumb from clay soil movement or a failed footing. Fixing the gate panel without fixing the post is a temporary fix at best. We repair the foundation of the problem first. That’s true on a $1,200 ranch gate and a $10,000 ornamental entry gate alike, and it’s how we protect your investment instead of nickel-and-diming it.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Bartonville since 2001.