Linear Welding & Fabrication Nationwide | Gatewood Fence & Gate

Linear Welding & Fabrication: The Denton Owner’s Guide

Linear welding & fabrication in Denton typically runs $240 to $680 installed, depending on whether we’re repairing a cracked gate frame, rebuilding a hinge post, or fabricating a replacement bracket that Linear no longer manufactures. We stock common Linear-compatible steel and aluminum stock on the truck, and most weld repairs happen same day or next morning. What usually brings a Denton homeowner to this page is a gate that suddenly drags on the driveway, a hinge that has torn loose from the post, or a weld that let go along the bottom rail after years of Texas sun and soil shifting.

Call (940) 394-8744

Here’s the thing about Linear gates: the opener and the electronics are solid, but the steel around them takes a beating. Denton’s clay soil expands and contracts with every wet-dry cycle, and that movement gets transmitted right into the gate frame. The weld is where it shows up first. We see it every week, from Corinth to Sanger to the neighborhoods off Teasley Lane.

Which Linear Models This Applies To

Linear openers get mounted on gates from a dozen different fabricators, so the welding work isn’t model-specific to the opener itself. It’s the gate frame, hinge hardware, and mounting plates that fail, and those vary by who built the gate originally. What matters is the steel gauge and the hardware pattern. We work on Linear-equipped swing gates, slide gates, and the heavier linear-actuator setups on ranch entrances and shop drives.

The OEM versus aftermarket decision for Linear-specific steel parts comes down to what’s still available. Linear discontinued a lot of older mounting brackets and gate hardware years ago. When the original part is gone, we fabricate a replacement from the same gauge steel, match the hole pattern, and weld it in place. You won’t find that bracket on a shelf anywhere, but we can make it in the truck and have your gate closing by dinner. If it’s a common wear item like a weld-on hinge or a slide-gate roller bracket, we carry quality aftermarket equivalents that match or beat the original spec. The gotcha to watch: Linear slide gates on older residential installs in Denton often used 14-gauge posts. Those rust from the inside out. If you let it go too long, you’re not welding a bracket anymore, you’re rebuilding the post base.

Signs Your Linear Welding & Fabrication Is Failing

• The gate drags on the driveway at the latch end. The hinge post has shifted out of plumb or the bottom rail weld has cracked. The opener keeps pushing, the frame keeps bending, and the drag gets worse every week.
• A hinge pops or squeals when the gate moves. The weld holding the hinge to the post or the gate frame is failing. Squealing means metal on metal with no lubrication left, which accelerates the tear.
• Visible cracks in the gate frame, usually at the corners. Texas heat cycles and wind load flex the corners until the weld gives. Once you can see a crack, it’s spreading.
• The gate post leans even a few degrees. A leaning post means the concrete footing or the post base weld is compromised. The gate is now pulling itself apart every time it cycles.
• The Linear opener trips or binds mid-cycle. The motor senses resistance from a sagging or twisted frame and shuts off to protect itself. The opener isn’t the problem. The steel underneath it is.

Replacement Cost & What’s Included

Here’s the straight answer on price for Denton and the surrounding county. A simple weld repair on a cracked gate frame runs $240 to $340, including grinding, prep, weld, and paint. Rebuilding a hinge post with new weld-on hinges runs $350 to $520, depending on post condition and whether we need to pour a new footing. Full fabrication of a discontinued Linear mounting bracket or slide-gate roller plate sits at $180 to $320, with the price driven by steel gauge and how much grinding and fitting is involved. If the gate frame itself is too far gone, full replacement fabrication runs $1,400 to $3,200 for a standard driveway swing gate, but that’s a different conversation.

Every quote includes parts, labor, cleanup, and the weld itself. You get the price before we strike an arc, and it doesn’t change when the job is done. The work carries our 90-Day Done Right Promise in writing. If a weld cracks in 90 days, we come back and fix it. No charge, no argument.

DIY or Call Us?

Welding is not a driveway project. There’s no safe way to do it halfway. A grinder, a machine, shielding gas, the right rod, and a hundred hours of practice separating a good weld from a dangerous one. What you can safely do is identify the problem: walk the gate line, check for cracks, check the post plumb, note where the gate drags. Take pictures. Measure the gap at the crack. Then call us at (940) 394-8744 and tell me what you found. The person who answers is the person who’ll show up.

If the gate is still moving, we’ll be out same day or next morning. You’ll get an honest read on whether it’s a weld-only repair or a deeper steel problem, and the price will be in your hand before any work starts. No trip charge inside the county, and if you’ve got a written estimate from anyone else, we’ll give you a free second opinion on it.

FAQs

Call for a Straight Answer

If your Linear gate is dragging, cracking, or pulling a post out of the ground, the sooner you call the less steel we have to replace. We handle welding and fabrication for Linear, LiftMaster, Mighty Mule, and Ghost Controls gates, plus the seven other major brands. Call (940) 394-8744 and a live person answers, 24/7. You’ll get a real diagnosis on the phone, and a firm price before any torch gets lit. Leave your gate better than I found it, anything less and I haven’t done my job.

Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Denton and nearby areas.