Linear Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Linear Gate Parts & Welding in Denton: What to Know First

We’re an independent Linear service provider in Denton, and we stock or can source Linear gate parts same-week for most residential models. Typical parts and welding work runs $195 to $620 depending on what failed, and most jobs are done in one visit with welding done right in your driveway. Call (940) 394-8744 if your Linear gate is sagging, grinding, or won’t close.

Call (940) 394-8744

This page is for Denton homeowners with a Linear gate opener or gate hardware that’s started misbehaving. Whether you have an older Linear actuator that’s finally given up or a newer swing gate with a hinge tearing loose from the post, this covers what actually goes wrong and how we fix it without selling you a whole new system.

How Linear Products Fail - and How We Fix Them

• Linear swing gate hinges wallowing out the post holes. Linear swing gate systems are popular in Denton’s older subdivisions like Southridge and Idiot’s Hill, and we see the same failure over and over: the hinge bolts work loose inside the post because water gets in and rusts the threads. The gate starts dragging, then the opener strains, then the board burns out. We weld the hinge plates back solid or sleeve the post, then re-hang the gate so it swings free. That fixes the root cause instead of replacing the opener and calling it done.
• Linear actuator arms binding at the clevis pin. The Linear LRA and HSA series actuators use a clevis pin where the arm connects to the gate bracket, and that pin is a rust magnet in Denton humidity. When it binds, the gate moves in jerks and the motor pulls more amps than it should. We pull the pin, clean or replace it, grease it properly, and re-align the arm. Half the time the opener isn’t failing at all, it’s fighting a stuck pin.
• Slide gate rollers wearing flat on one side. Linear slide gate operators, including the older SL series still running in rural Denton County, ride on steel rollers that wear unevenly when the track isn’t perfectly level. Owners call us because the gate sounds like a freight train. We weld in new roller brackets, true up the track, and the gate rolls like it should. If the old rollers got ignored too long, we sometimes have to weld repair plates onto the bottom rail where the steel wallowed out.
• Gate frames cracking at weld joints on tubular steel. This one isn’t Linear-specific, but we see it on Linear installations all over Denton because many were installed 10 to 15 years ago with a little too much faith in manufacturer specs. The horizontal rail cracks right at the welded joint where it meets the vertical stile. We grind out the old weld, re-weld it hot with proper penetration, and add a gusset plate when the design allows. If your gate creaks every time the wind blows, that crack is already there.
• Linear control boards failing after repeated lightning strikes. Denton gets serious thunderstorms, and Linear boards are sensitive to power surges. The symptom is usually a gate that starts opening on its own or a keypad that won’t respond. But before we replace a board, we check the ground stake and the low-voltage wiring, because a bad ground will kill the new board within a season. We’ve seen too many Linear boards replaced twice by someone who never fixed the ground.

Our Linear Gate Parts & Welding Process

1. 1
   You call, a person answers. Not a voicemail, not a phone tree. We ask what the gate is doing, what model opener you have if you can see it, and when you need us there.
2. 2
   We show up and diagnose. Hal or a member of his crew comes out, runs the gate through its cycle, checks the hinges, rollers, actuator arm, and board. We tell you what we found in plain English and what can wait.
3. 3
   We decide parts: OEM or better aftermarket. For Linear actuators and boards, we use OEM parts or proven aftermarket equivalents that meet or exceed spec. For steel, hinges, and rollers, we often fabricate or upgrade beyond what the original install used. You’ll know what’s going on your gate and why.
4. 4
   The repair happens on site. Welding is done in your driveway, not hauled back to a shop. The gate stays on your property the whole time. No “we’ll bring it back next week.”
5. 5
   We test under real conditions. We run the gate a dozen times, check the safety edges if it has them, adjust the limits and force settings, and make sure the welds are dressed and painted to match.
6. 6
   You get the 90-Day Done Right Promise in writing. If something we touched isn’t right within 90 days, we come back and make it right. No runaround, no fine print.

What Linear Gate Parts & Welding Costs in Denton

What moves the price: how much steel has to be cut out, whether we need to pull the gate off to do it right, and whether the post itself is so gone it needs replacing instead of repairing. We quote the price before any work starts. That number doesn’t change. Estimates are free, and if you have a written estimate from another company, we’ll give you a free second opinion. Call (940) 394-8744.

Why Denton Homeowners Call Gatewood Fence & Gate for Linear Work

We’ve been fixing gates in Denton since 2001. Hal Gatewood grew up just off Loop 288 and never saw much reason to leave, which means when you call Gatewood Fence & Gate you’re calling a local shop with a published address and a license number anyone can look up. The name is on the shop, and the shop is down the road.

Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right, one call and Hal comes back, no runaround. We answer the phone with a live person 24/7. And if your Linear system is genuinely too far gone, we service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing too, so we can tell you honestly whether repair or replacement makes sense. Most of the time repair makes sense. That’s kind of the point.

Leave your gate better than I found it, anything less and I haven’t done my job.

FAQs