Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Access Control in Denton: What to Know First
Linear gate access control in Denton means keypads, remotes, phone entry, card readers, or video intercoms tied to Linear operators, and we fix all of it right here in Denton County. Most access control repairs take under two hours once we’re on site, and we won’t quote you one price on the phone and show up with another. If a Linear keypad stopped talking to the board, or a card reader quit after a storm, call (940) 394-8744 and a live person picks up.
This page is for homeowners and small-property owners who own a Linear system and don’t want a sales pitch. We’re an independent Linear service provider, not a manufacturer hotline, so we’ll tell you straight what’s worth fixing and what isn’t.
How Linear Products Fail - and How We Fix Them
Linear builds solid hardware, but every brand has its weak spots. Here’s what we actually see on Denton driveways and gates week after week.
- Linear Multi-Code keypads go dead after a hard rain. The 3089 and 4120 series keypads use a weather seal that gets brittle in North Texas heat, then lets moisture into the contact pads. The keypad looks fine from the outside, but the buttons stop registering. We open the housing, clean the contact surfaces, and replace the seal, not the whole keypad. Half the time the keypad itself is still good and a $4 seal beats a $90 replacement.
- Linear MegaCode remotes work intermittently because the receiver board has drifted. The MCT-3 and MT-2 remotes run on a fixed frequency, and on older Linear operators the receiver trim pot drifts just enough that the remote only works when you’re standing right next to the gate. A lot of companies will sell you a new remote first. We check the receiver alignment and the remote’s oscillator before we sell anything, because throwing a second remote at a drifted receiver just gives you two remotes that don’t work.
- Linear APeX series boards burn out channel outputs after a power surge. We’re in Texas. Storms roll through, the grid flickers, and the APeX board takes a hit. The motor still runs because the main relay survived, but the access control trigger channel is dead and your keypad or phone entry won’t open the gate. We test the relay channels individually, and if the board is toast we replace it with a genuine Linear part rather than a knockoff that fights the operator’s logic.
- Linear phone entry systems drop calls during peak heat. The AE-500 and AE-1000 telephone entry units get finicky when temperatures climb past about 95 degrees, which in Denton is roughly half the year. The internal power supply sags and the unit reboots mid-call. It’s almost never the phone line. We’ve learned to check the unit’s power rail and heat load first, which saves you from calling the phone company twice before somebody looks at the actual box.
- Linear card readers lose their programming when the battery-backed memory dies. The Linear AM3 and NRD series readers store card data in onboard memory with a battery backup. When that little coin cell dies, every card wipes itself, and suddenly nobody’s card works on a Tuesday morning. Reprogramming without replacing the battery means you’ll be reprogramming again in three months. We replace the cell, then reprogram from scratch, then test every card before we leave.
Our Linear Gate Access Control Process
Here’s what a Linear access control job looks like when you call us.
- 1
You call, we answer. Not a voicemail. Hal or one of his guys asks what the gate is doing, what brand and model you have, and when you need it fixed.
- 2
We show up and diagnose. We test the access control device first, then the wiring, then the operator board. Nine times out of ten the problem isn’t where the last guy looked.
- 3
We quote the repair before we touch anything. You’ll know the price and what parts we’re using. If the part needs to be ordered, we tell you exactly how long that takes.
- 4
We fix it on site. We carry common Linear parts on the truck, and if we need to wire, splice, or weld, we do it right there in your driveway.
- 5
We test it like we own it. Every remote, every keypad code, every card, every phone entry button gets tested until it works every time.
- 6
You get the 90-Day Done Right Promise in writing. If it’s not done right, we come back and make it right. One call, no runaround.
What Linear Gate Access Control Costs in Denton
Straight numbers, because that’s how we do business. A Linear gate access control repair in Denton typically runs between $120 and $380 depending on what failed.
- Keypad replacement or repair: $120-$240 installed, depending on whether we’re rebuilding the seal or swapping the whole unit.
- Remote programming or replacement: $45-$90 for a new MegaCode remote programmed and tested.
- Receiver board replacement: $180-$320 for a genuine Linear board, including labor.
- Phone entry system repair: $200-$380, depending on the power supply fix or board swap.
- Full access control refresh (keypad + receiver + two remotes): $350-$500 installed, tested, and warranted.
What moves the price is which Linear series you have, how old the equipment is, and whether we’re repairing a board or replacing it. Estimates are free, the price is set before work starts, and we won’t surprise you when the invoice comes. Call (940) 394-8744 if you want a real number for your specific system.
Why Denton Homeowners Call Gatewood Fence & Gate for Linear Work
Hal Gatewood grew up just off Loop 288 on the north side of Denton and never saw much reason to leave. The shop is down the road, his name is on the building, and if you want to look him in the eye before he touches your gate, you can literally drive over and do that. We’ve been fixing gates in Denton since 2001, and we fix what other companies want to replace because we’d rather weld on site than haul your gate off and sell you a new one. We’re certified to service nine major brands, so if you’ve got a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing operator somewhere on the property too, the same person fixes all of it in one trip. And every job carries the 90-Day Done Right Promise, in writing, because that’s how Hal would want it done at his own place. Leave your gate better than I found it, anything less and I haven’t done my job.
FAQs
Yes, we can usually repair it on the spot in Denton by cleaning the corroded contact pads and replacing the dried-out weather seal, and that typically costs far less than a new keypad. If the seal has been bad long enough that the board itself is corroded, we’ll quote a replacement before doing anything. Call (940) 394-8744 and we’ll tell you which one it looks like over the phone.
Usually it’s not the remote, it’s the receiver board on the operator that has drifted off frequency, and the fix is re-aligning or replacing the receiver rather than buying a second remote. We test the remote’s output and the receiver’s sensitivity before recommending anything. If it is the remote, a new MegaCode unit is affordable and we program it on site.
No, it’s not normal, and in Denton it’s almost always the internal power supply sagging under heat load, not the phone line. We check the power rail and the unit’s heat load first, which usually saves you the cost of a phone company service call that wouldn’t have found anything. It’s a known weak point on the AE-500 and AE-1000 series.
We’re an independent Linear service provider, not a factory-authorized shop, which means we can install aftermarket parts when they’re genuinely better and genuine Linear parts when warranty coverage matters. We don’t have a manufacturer mandate to sell you a whole new board when a $5 component fixes the problem. That independence works in your favor.
We answer the phone 24/7 and we’ll schedule you for the first available window, often the same day for a gate that won’t open at all. If it’s a keypad that’s intermittent, we might schedule you for the next morning. Either way, you’ll talk to a person who knows Linear equipment, not a call queue.
Call Gatewood Fence & Gate for Linear Access Control in Denton
If your Linear keypad, remote, card reader, or phone entry isn’t doing what it should, call (940) 394-8744. Hal or someone who works for him will answer, tell you straight what it probably is, and give you a free estimate before any work starts. We fix Linear access control the right way in Denton, and we’ve been doing it for over two decades. If you’d rather skip the phone, drive by the shop and see the name on the building for yourself.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Denton and nearby areas.