Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Denton: What to Know First
FAAC gate installation in Denton typically runs $1,800 to $6,400 depending on the gate type, operator model, and whether we’re working with an existing frame or building from scratch. Most FAAC installs take one to two days on site, and we quote the full job before a single tool comes off the truck. If you’re reading this, you likely own a FAAC operator or you’re considering one, and you want someone who actually knows how these things behave in Texas clay soil and hundred-degree summers, not someone learning the wiring diagram off a YouTube video in your driveway.
This page is for FAAC owners in Denton who need a gate installed right the first time. Hal Gatewood and his crew handle FAAC swing, slide, and hydraulic operators as an independent FAAC service provider. We’re not affiliated with or authorized by FAAC, but we’ve been installing and servicing their equipment since before half the national gate companies had a website. Call (940) 394-8744 and Hal will talk you through what you’ve got and what it’ll take.
How FAAC Products Fail - and How We Fix Them
- FAAC 390 and 391 swing operators with stripped release keys. These residential swing arms use a plastic manual-release key that gets brittle after five or six Texas summers. The key shears off inside the operator body, and suddenly the gate won’t disengage. We see this on roughly one in four FAAC 390 installs older than eight years. Fix: we extract the broken key, replace the release assembly with the OEM part, and apply dielectric grease so the next release doesn’t weld itself in place.
- FAAC 750 and 844 hydraulic operators with weeping seals. Denton’s temperature swings, from mid-20s in February to 105 in August, are hard on hydraulic seals. A FAAC 844 that sat through a few freeze-thaw cycles will start weeping oil at the ram, which drops operating pressure and makes the gate slow and noisy. Fix: reseal the ram, flush the hydraulic circuit, and refill with the correct FAAC-spec fluid. We do this in the driveway, not on a bench back at a shop somewhere.
- FAAC E024U control boards with phantom limit faults. The E024U board runs the 750 and 844 series, and it’s notorious for throwing limit faults when the gate is nowhere near the limit. Nine times out of ten, the board is fine: the problem is oxidized terminals where the limit switch wiring lands. Fix: pull each terminal, clean the contact, re-seat the wire, and re-run the learn cycle. If the board is genuinely dead, we’ll tell you before quoting a replacement and show you the old one.
- FAAC 412 and 415 operators with capacitor failures after power surges. Denton gets real lightning, and the municipal grid isn’t always gentle. A FAAC 412 that worked fine until a storm rolls through and now just hums usually has a swollen start capacitor. Fix: replace the capacitor with the correct microfarad rating, test the run winding, and add a surge protector at the disconnect box so it doesn’t happen again next spring.
- FAAC C720 and C721 sliding gate operators with misadjusted torque limiters. Sliding gates on uneven Denton driveways, especially in older neighborhoods like Idiot’s Hill or along Frame Street, bind if the track settles even a quarter inch. The torque limiter starts slipping to protect the motor, and the gate stops mid-travel. Fix: check the track for settlement, re-level the V-groove wheels, then set the torque limiter per FAAC’s spec so it slips at the right load and not before.
Our FAAC Gate Installation Process
- 1
You call and a real person answers. Not a voicemail, not a call center. Hal or his crew picks up at (940) 394-8744 and asks what the gate is doing, or what you want it to do.
- 2
We show up, look, and measure. Hal comes out, walks the gate line, checks the hinge posts, the track, the power situation, and the operator you already have. If the post is rotten or the conduit is undersized, he’ll tell you then, not after the concrete is poured.
- 3
We make a parts decision with you in the loop. For FAAC operators, OEM parts are the default when the part matters: control boards, hydraulic rams, limit assemblies. For things like photo eyes, edge sensors, and external receivers, we’ll offer a quality aftermarket option if it’s equal or better and saves you money. We don’t sneak in parts that void your warranty.
- 4
The install happens in your driveway. We weld on site when steel needs welding. If a hinge post needs to be set, we set it and let it cure properly before hanging the gate, no shortcuts.
- 5
We run the FAAC learn cycle and test every safety device. The operator gets programmed to the gate’s weight, travel, and obstruction settings. Photo eyes, edges, and the manual release all get tested with weight on the gate, not just on the bench.
- 6
You get the 90-Day Done Right Promise in writing. Before we leave, we walk the gate with you, show you what we did, and hand you a written guarantee. If it’s not right, we make it right. One call brings Hal back.
What FAAC Gate Installation Costs in Denton
| Job | Typical Range |
|---|---|
| FAAC 390 or 412 swing operator install (existing gate) | $1,800 - $2,800 |
| FAAC 750 or 844 hydraulic swing operator install | $3,200 - $4,800 |
| FAAC C720 or C721 sliding operator install (existing track) | $2,400 - $3,800 |
| Full double swing gate build with FAAC 750 pair | $4,500 - $6,400 |
| Pedestrian gate with FAAC 390 and maglock | $2,200 - $3,200 |
What moves the price: gate weight and panel material, whether the posts are plumb or need to be reset, how far the power is from the operator, and whether we’re reusing an existing track or running new. In Denton, the soil shifts with the seasons, so gates in areas with black clay, anywhere off Mayhill Road or down toward Sanger, often need a deeper footing that adds a few hundred dollars. We don’t pad estimates for that; we just tell you what’s needed. The price is quoted and agreed before any work starts. Call (940) 394-8744 for a free estimate, no trip charge inside the county.
Why Denton Homeowners Call Gatewood Fence & Gate for FAAC Work
Hal Gatewood grew up just off Loop 288 on the north side of Denton and has never had much interest in leaving. He’s been at this since 2001, and the name is on the shop and on every invoice. That means something when you’re spending five grand on a gate system and you want someone you’ll see at the Denton Community Market, not a truck that disappears into a corporate fleet. Every FAAC job carries the 90-Day Done Right Promise in writing: if it’s not done right, we make it right, no runaround. A live person answers the phone 24/7, and that person is usually sitting in Denton, not three states away.
We also service the other major brands: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. So if your FAAC operator turns out to be beyond saving and a different brand makes more sense for your gate, we’ll tell you straight and install it right. That’s the advantage of an independent shop: we recommend what fits your gate and your budget, not what earns us a spiff from a manufacturer.
FAQs
It depends on what failed and whether the install caused it. In our experience, FAAC honors warranty claims when the operator was installed correctly and the gate itself is within the operator’s rated weight and cycle limits. What voids a warranty, and what we see too often in Denton, is a gate that was never balanced before the operator went on. A heavy or binding gate burns up boards and motors, and the manufacturer can tell. We check gate balance and travel before we ever mount a FAAC operator, and we document it.
Most FAAC swing operator installs happen within three to five business days of the estimate. Sliding gates and jobs that need new posts or concrete work take longer because the concrete has to cure before the gate goes on. If your gate is stuck closed and you’re trapped, call (940) 394-8744 and Hal will talk you through getting it open, usually that same day, before we even schedule the install.
For control boards, hydraulic components, limit systems, and anything inside the operator housing, we use OEM FAAC parts. That’s the safe choice for performance and warranty. For accessories like photo eyes, edge sensors, keypads, and receivers, we’ll offer quality aftermarket parts when they’re equal or better and cost less. You always know what’s going on your gate before it goes on.
If the operator is over 15 years old, has had two or more board failures, or the cost to repair is more than 60% of a new unit, we’ll tell you it’s time to replace. If the gate itself is the problem, sagging hinges, a rotted post, a warped panel, then a new operator won’t fix it and you’ll be back in the same spot next year. We diagnose the whole system, not just the box on the post.
Denton and the surrounding county: Corinth, Sanger, Krum, Argyle, Aubrey, Pilot Point, Ponder, and the unincorporated areas in between. No trip charge inside the county, and we publish our address so you can look us up before you call. Leave your gate better than I found it, anything less and I haven’t done my job.
If you’ve got a FAAC gate that needs installing, or one that’s been limping along and you’re tired of resetting the breaker, call (940) 394-8744. Hal will answer, ask the right questions, and give you a straight answer and a free estimate for gate installation in Denton. Se habla español.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Denton and nearby areas.