Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Access Control in Denton: What to Know First
We service and repair FAAC gate access control systems across Denton, and most jobs are done the same day we arrive at your driveway. An independent FAAC service provider, Gatewood Fence & Gate handles keypads, card readers, phone entry, and video intercoms on FAAC swing and slide gate operators, with pricing quoted and agreed before we turn a single screw. If you own a FAAC gate in Denton and the keypad stopped talking to the operator or the remote only works when it feels like it, this page will walk you through what’s actually going wrong and what it costs to fix. Call (940) 394-8744 for a free estimate.
This page is written for FAAC owners in Denton, Corinth, Sanger, Argyle, Krum, and the rural pockets around Denton County who want to understand their system before spending a dime. We’ll name the specific FAAC model lines we see in this area, the failure patterns they share, and what a real repair looks like from start to finish.
How FAAC Products Fail - and How We Fix Them
- FAAC 412 and 415 operators losing keypad sync after power blinks. Denton’s spring storm season knocks out power for a few seconds, and the FAAC 412 compact 24V operator is especially prone to dropping its programmed keypad codes. We re-flash the board, verify the memory is stable across repeated power cycles, and re-program your access codes. The fix takes under an hour.
- FAAC E024U control boards with dead relay channels. The E024U is the brain inside the 412 and 415 lines, and when one relay channel dies, the keypad still beeps but the gate never opens. We test each channel with a multimeter, and when a relay is truly dead, we replace the board with an OEM unit rather than soldering on a workaround that quits in six months.
- Weather-worn photocell wiring on FAAC swing gate systems in rural Denton County. FAAC operators use a simple two-wire safety photocell circuit, and on properties with cattle or deer, the wiring near the gate posts gets chewed or pinched. When the safety inputs read intermittently, the gate either refuses to open or reverses mid-cycle. We trace the circuit end to end, replace the brittle wire, and seal the junction boxes against moisture.
- Remote range dropping off on FAAC 750 and 844 slide gate operators. The plug-in receivers on these slide gate operators pick up interference from nearby LED yard lights and transformer hum that’s common in Denton’s newer subdivisions. We test the receiver’s antenna position, relocate or shield it, and swap in FAAC-compatible remotes only when the frequencies are confirmed clean.
- Corroded keypad housings on FAAC DigiKey and Deco line keypads. Denton’s summer heat and occasional hard freeze cycle cracks the gasket seal on older FAAC standalone keypads. Water gets in, the membrane degrades, and buttons stop responding or start ghost-pressing digits on their own. We replace the housing and membrane with FAAC parts when production units are available, or a sealed aftermarket membrane with a matching footprint when FAAC has discontinued the line. You find out which you’re getting before we order it.
Our FAAC Gate Access Control Process
Every FAAC job starts the same way: a phone call where a live person answers. Not a voicemail. From there, here’s how a typical access control repair or upgrade goes.
- 1
The call and the questions. We ask what the gate is doing, what FAAC operator model you have if you know it, and when the problem started. Most people don’t know the model, so we’ll pull it off the motor housing when we arrive.
- 2
On-site diagnosis. Hal Gatewood or one of his crew shows up at your address in the window we gave you. We test the keypad, the receiver, the control board inputs, and the safety circuit, then show you exactly which component is failing before we fix or replace anything.
- 3
The parts decision. We lay out the options: OEM FAAC parts when the warranty matters and the lead time is days, or a proven aftermarket part when it’s equal quality and half the wait. You decide, and the price is quoted and agreed before any work starts.
- 4
The repair or upgrade. We make the fix in your driveway. That includes programming new remotes and keypad codes, re-sealing enclosures, and replacing any wiring that’s brittle or waterlogged.
- 5
The test cycle. We run the gate through thirty cycles with each access device, kill the power twice to confirm memory retention, and test the safety reverse. If a neighbor’s remote accidentally opens your gate, we’re not done.
- 6
Cleanup and the promise. We walk you through the work, hand you a written invoice with the 90-Day Done Right Promise stamped on it, and leave your gate better than we found it. Anything less and we haven’t done our job.
What FAAC Gate Access Control Costs in Denton
Here’s where Denton FAAC owners stand, based on the jobs we run week in and week out. These are the numbers we quote over the phone so there are no surprises at the door:
- Keypad replacement or re-programming: $180 - $320 depending on whether it’s a membrane repair or a full keypad swap.
- Standalone receiver replacement or antenna relocation: $150 - $280.
- Control board repair or replacement (E024U): $350 - $650, OEM board included in the range.
- Full access control upgrade (keypad, receiver, remotes, safety check): $600 - $1,100.
- Phone entry or video intercom integration: $450 - $950 depending on wiring runs and whether we’re adding a cellular adapter.
What moves the price is parts availability, the age of your FAAC operator, and whether we’re repairing or replacing a failing component. We’ll always tell you if your gate only needs a $200 fix and not a $600 board. Call (940) 394-8744 for an exact quote, and ask about the $40 off any repair over $200.
Why Denton Homeowners Call Gatewood Fence & Gate for FAAC Work
We’ve been fixing gates and running fence lines in Denton since 2001, and we haven’t had to chase work with Google ads or a jingle since about 2003. Hal Gatewood grew up just off Loop 288 on the north side of Denton, and he’s spent the last twenty-plus years fixing what other outfits would rather replace. If you own a FAAC gate, you’ll get somebody who knows the brand’s quirks and won’t pretend another brand’s parts fit where they don’t.
When the FAAC repair is going to take a few days for parts, we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing systems in Denton. Point being, if you call us about one brand and we find a different problem, we can handle it. Every job carries the 90-Day Done Right Promise in writing, and the person who shows up at your gate is either Hal or somebody who answers to him. That’s the whole accountability structure. There isn’t a call center three states away and never will be.
FAQs
In most cases, yes, and it’s one of the more common FAAC access control repairs we do in Denton. The repair time depends on whether the keypad is responding and just needs re-programming or whether the membrane and board have to be replaced. The replacement parts usually sit in stock locally. Call (940) 394-8744 and we’ll give you a straight answer and an arrival window, not a four-hour hold time.
If your FAAC operator is still under the manufacturer’s warranty, we install OEM FAAC parts so the warranty stays intact. If the unit is out of warranty, we’ll talk through aftermarket options that perform as well as OEM and cost less. Either way, you know which part you’re getting and why before we put it in.
It depends on the failure mode. If the keypad loses programming, the gate stays unlocked until the codes are restored. If the control board relay dies, the gate often locks and won’t budge from any access device. When a FAAC gate in Denton stops responding to everything at once, we check the 24V supply first, because a bad transformer kills every access device at once and the fix is often faster and cheaper than people expect.
If the operator itself is still running smoothly and the failure is in the keypad, receiver, or board, repair is almost always the better call. FAAC operators from the 412, 415, 750, and 844 lines have solid mechanicals that run for years, and a board or keypad swap gets them back on duty without the $3,000-plus cost of replacing the whole gate system. We’ll tell you if the operator is too far gone, but in our experience the motor is rarely the problem.
No. We’re an independent FAAC service provider, not an authorized FAAC warranty station. If your unit is under manufacturer warranty, we’ll install OEM FAAC parts to keep that warranty alive, but we don’t bill FAAC direct. What we do bring is 29-plus years of local gate work and the 90-Day Done Right Promise on every job we complete.
If your FAAC gate in Denton isn’t opening when it should, call (940) 394-8744 and talk to a live person. We’ll get you on the schedule and give you a straight price before we start. No trip charge inside Denton County, and if you’ve got a written estimate from another shop, bring it and we’ll give you a free second opinion.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Denton and nearby areas.