Elite Gate Installation Nationwide | Gatewood Fence & Gate

Elite Gate Installation in Denton: What to Know First

Elite gate installation in Denton runs $1,850 to $6,400 for most residential jobs, depending on whether you’re doing a single swing gate or a full double-gate system with automation. We install, weld, and service Elite operators and gate hardware as an independent provider, not a manufacturer shop, and we typically have the gate swinging within three to five business days of measure. You’ll get a written quote before any work starts, and the number we give you is the number you’ll pay.

Call (940) 394-8744

This page is for the Denton homeowner who bought an Elite gate or operator and now needs it installed properly, or who has one that was installed wrong and needs it straightened out. If that’s you, call (940) 394-8744 and Hal will walk you through what you’ve got.

How Elite Products Fail - and How We Fix Them

Elite gates are solid equipment, but we’ve been called out to enough of them in Denton County to know where they tend to struggle. Here’s what we see most often:

• Elite SL3000 slide operator gear wear. The plastic drive gear inside the SL3000 series strips when the gate runs against a misaligned track or when the rollers haven’t been greased. You’ll hear the motor spinning but the gate won’t move. We pull the cover, replace the gear, and realign the track so it doesn’t chew through another one.
• Phantom eye false triggers on Elite swing systems. The Elite photo-eye sensors get crusty with Denton dust and hard water spots from sprinklers hitting the posts. The gate thinks something’s in the way and refuses to close, or reverses halfway. Most of the time it’s a cleaning and a re-aim, not a new sensor.
• Hinge post flex on heavier Elite double gates. A double swing gate that’s dragging on the latch side usually means the hinge post was set without enough concrete. The wind load across a big Elite double gate pushes the post out of plumb. We dig it out, re-set the post with a proper footer, and weld a gusset plate so it stays put.
• Elite control board relay failure after storms. North Texas lightning loves a gate opener. The SL1000 and SL3000 boards have relays that stick or cook after a close strike. We test the board in place before quoting a replacement, because sometimes it’s just the relay and not the whole board.
• Chain tension issues on Elite slide operators. The chain on an Elite sliding gate stretches in the Texas heat - summer after summer it gets a little looser until the gate jerks instead of rolling. We adjust the tension at the turnbuckle and set the limit switches fresh. Tight chain equals a gate that actually stops where it’s supposed to.

Our Elite Gate Installation Process

We don’t sell you a box and point you to the manual. Here’s what a typical Elite install looks like with us from the first call:

1. 1
   You call (940) 394-8744. A live person answers, day or night. Hal asks what gate you’ve got, what’s happening, and whether it’s a new install or a repair of existing Elite hardware.
2. 2
   We come out and measure. We look at the doorway width, the slope, the soil under the concrete, the power situation at the pillar. Hal writes it all down in front of you.
3. 3
   You get a written quote. Exact number, no range, no drive-time surprise. We quote OEM Elite parts where they matter for warranty, and tell you honestly where a quality aftermarket part is the better money for a 12-year-old gate.
4. 4
   We do the work in place. We weld on site, not in a shop. The gate stays in your driveway, and the welds are done to hold up to Denton wind and heat. No hauling your gate across town.
5. 5
   We test and adjust in front of you. We run the gate through full cycles, set the limits, test the safety edges, and show you what the operator sounds like when it’s healthy.
6. 6
   You get the 90-Day Done Right Promise in writing. If something’s not right, one call brings Hal back. No runaround, no service ticket dance.

What Elite Gate Installation Costs in Denton

Here’s the honest range on the Elite jobs we do most in the Denton area:

• Single swing gate with Elite operator: $1,850-$2,800
• Double swing gate with Elite operator and welded posts: $3,200-$4,800
• Sliding gate with Elite SL3000 operator: $2,600-$4,200
• Elite operator replacement on an existing gate (operator only): $900-$1,650
• Pedestrian gate with Elite keypad access: $1,100-$1,900

What moves the price is concrete work, the weight of the gate, and whether we’re running new electrical for the operator or using an existing line. Every quote is written, itemized, and agreed before the first weld. Estimates are free, and there’s no trip charge inside the county.

Why Denton Homeowners Call Gatewood Fence & Gate for Elite Work

Hal Gatewood grew up off Loop 288 on the north side of Denton and has been doing this since 2001. He’s the man who answers the phone at midnight and the man who shows up to fix it the next morning. The name is on the shop, and the shop is down the road - that’s the oldest accountability there is.

We carry OEM Elite parts for the common failures and stock quality aftermarket options when they make more sense. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has mixed operators we handle all of it in one call. Every job comes with the 90-Day Done Right Promise in writing. If it’s not done right, we make it right.

FAQs