Linear Keypad & Intercom Repair Nationwide | Gatewood Fence & Gate

Linear Keypad & Intercom Repair: The Denton Owner’s Guide

We stock and install Linear-compatible keypads and intercoms, and most replacements in Denton run between $260 and $540 installed depending on whether the part can be repaired on the board level or needs a full swap. We carry the common Linear parts on the truck, so a dead keypad or crackling intercom is usually a same-day fix when you call before noon. The way most people find out is simple: the keypad lights up but the gate won’t move, or the intercom rings inside and sounds like someone crumpling a potato chip bag instead of a voice.

Call (940) 394-8744

Which Linear Models This Applies To

Most of the Linear keypads we see in Denton are the AE-100, AE-2000, and MEGACODE series, along with the AM-KP keypads that pair with the MEGACODE and Delta-3 receivers. The intercoms are usually the AM-3 line or the older AE-500 telephone entry units. Linear changed connector styles and voltage tolerances across generations, and here’s a gotcha we run into weekly: an older AE-100 keypad mounted before 2008 often won’t be a drop-in match for a new MEGACODE receiver because the wiring pigtail changed from four wires to five. Before you buy a part off a big-box shelf, flip the keypad over and check the model sticker. We can match nearly all of them, and for Linear specifically we prefer OEM modules inside the keypad when they’re still available because the aftermarket boards don’t always hold up to Texas sun fade on the membrane. For metal enclosures and mounting boxes, a good powder-coated aftermarket is usually fine and saves you real money.

Signs Your Linear Keypad & Intercom Repair Is Failing

• Keypad lights up but the gate doesn’t respond. This usually means the wiring between the keypad and the operator has a cut or a corroded splice. We find a lot of these in Denton where weed eaters or aeration work clipped the buried line on the property edge.
• Some keys require three or four hard presses to register. The membrane under the buttons has worn through or collected moisture. This isn’t a cleaning job, it’s a membrane replacement inside the unit.
• Intercom buzzes constantly or only works one direction. The audio transformer inside the handset takes a beating in North Texas heat, especially if the unit was mounted on an unshaded brick column. One direction failing is usually a loose wire on the speaker terminals.
• Keypad works fine in the morning but dead by afternoon. This is a classic expansion-contraction issue. The connector from the keypad harness to the operator’s board spreads just enough in the heat to break contact, then closes again overnight.
• You hear a click when you enter a code but the gate doesn’t move. The keypad relay is firing. The problem is the gate operator’s limit switch or battery. We check both before we ever sell you a new keypad.

Replacement Cost & What’s Included

In Denton, a keypad swap typically lands between $260 and $380 installed. A new telephone-entry intercom usually runs $420 to $540. Board-level repair on a keypad, when the housing is still solid, can be as low as $180 to $240. What drives the range is whether we can save the existing enclosure and mount, whether new wire needs to be pulled, and whether we’re matching an older Linear receiver or starting fresh. The price Hal quotes you over the phone is the price on the invoice. We don’t add trip fees inside the county, and every parts install carries our 90-Day Done Right Promise in writing: if the part fails or something about the install isn’t right, call and we come back. No arguing about it.

DIY or Call Us?

If the keypad simply stopped working after a storm, check your gate’s main breaker and your GFCI outlet first. That’s free and worth doing. But the moment you’re unscrewing the keypad housing and looking at the pigtail wiring or the relay board, you’re into territory where one crossed wire can fry the operator board behind it, and that’s a $400 part instead of a $280 keypad. Keypads and intercoms carry low voltage, so the main risk isn’t a shock. It’s wiring it wrong and taking out the receiver. If you’re not comfortable identifying the relay trigger wire from the common, call us at (940) 394-8744 and we’ll walk the job with you first over the phone. Sometimes what sounds dead is just a loose wire at the operator, and we can save you a service call by talking you through checking it.

FAQs