Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Hinge & Roller Replacement: The Denton Owner’s Guide
FAAC hinge and roller replacement in Denton typically runs $140 to $310 installed, depending on the model and how many rollers the gate carries. We stock FAAC-compatible hinges and rollers on the truck and can usually have the swap done the same day we look at it. Most folks figure out something’s wrong when the gate starts groaning on the way open, or the panel drops about a half inch and drags a scar into the driveway.
That drag is the tell. A FAAC gate that catches near the latch side almost always has a worn roller or a hinge pin that’s ovaled out. Left alone, the gate starts leaning on the operator, and then you’re swapping a motor instead of a $20 part.
Which FAAC Models This Applies To
FAAC builds hinge and roller hardware for its 390, 412, S418, C720, C721, and 844 series operators, but the roller assembly varies by gate weight and panel style. The 412 and S418 lines mostly use a 6mm hinge pin with a nylon-bushed roller, while the heavier C720 and C721 gear-driven units run an 8mm pin and a sealed roller. The quick check: measure the roller diameter and the pin thickness before you order anything.
Here’s the compatibility gotcha most parts catalogs miss: FAAC changed the roller bushing material around 2014, and the older metal-sleeved rollers don’t seat correctly in the newer housings without a shim. If your gate was installed before 2014 and someone hands you a roller that “should fit,” make them test it before they bolt anything down. We stock OEM FAAC parts when the warranty matters, and a quality aftermarket equivalent for the older series where FAAC no longer stocks the original.
Gatewood Fence & Gate is an independent service provider, not affiliated with FAAC, and we’re certified to service their hardware alongside LiftMaster, Mighty Mule, Ghost Controls, and the rest of the major brands.
Signs Your FAAC Hinge & Roller Replacement Is Failing
- Gate sags toward the latch side. The roller has worn flat or the hinge pin has gone oval. Denton’s summer heat accelerates the wear because the nylon bushing dries out and gets brittle faster than it does in cooler climates.
- Groaning or screeching when the gate moves. A dry, metal-on-metal sound means the roller bearing has lost its grease or the pin is binding. WD-40 won’t fix it; it just quiets it for a week and draws in more grit.
- Gate hesitates or jerks near the closed position. The operator is fighting a hinge that doesn’t want to swing. FAAC motors are tough, but they’re not designed to muscle a seized roller all day.
- Visible flat spot on the roller. Run your finger along the bottom of the roller once the gate is cool. A flat spot tells you the roller stopped rolling and started sliding, which means the bearing is done.
- Rust staining below the hinge pin. That’s not cosmetic. A rust trail means the pin and bracket are deteriorating from the inside, and the roller is next.
Replacement Cost & What’s Included
A single FAAC hinge and roller replacement in Denton lands between $140 and $310 installed. The range comes down to the model, the number of rollers, and whether the hinge bracket itself needs welding or just a fresh pin. Most FAAC gates run two rollers, and our price includes the parts, the labor, the alignment check, and a load test on the operator.
You get the number before any work starts. No surprises at the door, no “we found something while we were in there” without a phone call first. Every hinge and roller job leaves with the 90-Day Done Right Promise in writing. If it’s not right, one call brings Hal Gatewood back, no runaround. And the price you agree to is the price you pay.
DIY or Call Us?
You can safely check a few things yourself: run your hand along the roller for flat spots, look for rust staining under the hinge pin, and eyeball the gap between the gate and the post on both sides. That’ll confirm what’s failing. But swapping a FAAC roller means lifting the gate panel off its hinges, and a 300-pound gate leaning against you is not something to handle alone.
If the gate is on an incline, the panel wants to fall toward the street even before you unbolt anything. We’ve watched homeowners prop a gate with a 2×4 and a prayer, and we’ve also fixed the dents. This is one of those repairs where the tool list is short but the consequences of a slip are long. Call us at (940) 394-8744 and we’ll have it sorted the same day in most cases.
FAQs
In Denton, expect 5 to 8 years from the rollers and 8 to 12 from the hinges before the heat and grit start taking a toll. Gates on gravel roads wear faster because the dust works into the bearing and grinds it from the inside.
Sometimes. If the bracket is solid and only the pin is ovaled, we can weld in a new pin sleeve and press in fresh bushings on site. If the roller bearing has seized, replacement is cheaper than a rebuild, and we stock both OEM and aftermarket options on the truck.
Most single-panel FAAC hinge and roller replacements take 45 minutes to an hour and a half, including re-aligning the gate and testing the operator. Two rollers or a welded bracket repair can push it to two hours.
We keep the common FAAC 6mm and 8mm rollers, hinge pins, and bushing kits on the truck, along with parts for LiftMaster, Mighty Mule, Ghost Controls, and other major brands. If your gate is an oddball, we can usually have the right part by the next morning.
If your FAAC gate is dragging, groaning, or sagging, call us at (940) 394-8744. Hal Gatewood answers the phone himself, any hour. We’ll tell you what’s failing, what it costs to fix, and whether it’s worth fixing at all. Leave your gate better than I found it, anything less and I haven’t done my job.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Denton and nearby areas.