Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Denton?
Gate access control installation in Denton typically costs between $650 and $2,800, depending on whether you are retrofitting an existing gate operator or installing a new system from scratch. Simple keypad or remote entry additions usually fall on the lower end, while complex cellular, video-intercom, or multi-user systems for properties near the University of North Texas or rural acreage in Ponder run toward the higher end of that range. We provide upfront pricing for every job, so you never have to guess what the final bill will look like.
Gate Access Control Cost Breakdown (2026)
When you look at access control, you aren’t just paying for a keypad; you are paying for the hardware, the wiring, and the integration with your existing gate motor. Because we handle everything from basic LiftMaster remotes to advanced Viking or DoorKing systems, we see a wide range of setups. Here is what you can expect to pay for specific access control components in the Denton market this year.
| Access Control Upgrade | Estimated Cost Range (Parts & Labor) |
|---|---|
| Standard Wired Keypad | $650 - $950 |
| Wireless Keypad & Receiver | $450 - $700 |
| Cellular Intercom System | $1,200 - $2,200 |
| Video Intercom Integration | $1,500 - $2,800 |
| Telephone Entry System (Multi-User) | $2,000 - $3,500+ |
| Safety Loop/Sensor Add-on | $500 - $900 |
These numbers assume a straightforward installation. If your gate post is already wired and the motor supports the new device, you will be on the lower end of these ranges. If we have to trench wire across a driveway or troubleshoot an old, corroded control board to get the new system talking to your gate, the labor hours go up. My name is Hal Gatewood, and I have been doing this since 2001. I have seen enough gate installs in Denton to know that most of the cost variation comes from the condition of your existing electrical run. If you want an exact number for your property, call (940) 394-8744 for a free estimate.
What Affects Gate Access Control Pricing in Denton
Not every gate is the same, and neither is the electrical environment at your property. When I come out to look at a gate, I am checking for specific variables that dictate the final price. Here is what usually moves the needle on your quote:
- Existing Power and Wiring: If you have a dedicated power line already run to your gate post, your install cost is significantly lower. If we have to trench new conduit to meet current code, you are looking at additional labor and materials.
- Gate Operator Compatibility: Some older gate openers-especially those installed before 2010-struggle to communicate with modern smart access systems. Upgrading the main control board to make it “smart-ready” is a separate cost from the keypad itself.
- System Complexity: A basic keypad is a one-time hardware cost. A cellular or video-intercom system requires a monthly subscription plan for the data, and the hardware itself is more expensive to install and configure.
- Safety Requirements: If your gate lacks modern safety sensors (like photo eyes or contact edges), we cannot legally or safely install certain access control systems without bringing the safety features up to current standards. Cutting corners on safety is how people get hurt, and I won’t do it.
- Property Geography: We work all over Denton County, from the tight spaces in historic neighborhoods to long, winding driveways in rural areas. Long runs of wire for exit wands or safety loops add material costs and time, which is reflected in the estimate.
How to Save on Gate Access Control
You don’t need to overspend to get a reliable, secure gate system. Over the last 29 years, I have learned that the best way to save money is to avoid “disposable” hardware that breaks every two years. Here are a few ways we help our neighbors in Denton keep costs down.
- Repair Before Replace: A lot of companies will tell you to replace the whole motor just because a keypad failed. Often, the motor is fine, and we can just replace the control board or the receiver. We specialize in Gate Access Control in Denton that fixes the actual problem, not just the symptom.
- Use Our Standing Discounts: We offer a permanent 10% discount for seniors and veterans. If you have a repair bill over $200, we take $40 off immediately. No coupons required.
- Get a Second Opinion: If another company told you that you need a $5,000 overhaul, call us. We offer free second opinions on written estimates. If your current system can be saved, I will tell you how to save it.
- Keep the Gate Maintained: A gate that drags on the ground puts massive strain on the motor and the access control board. Keep the hinges greased and the gate level. If the gate moves smoothly, the electronics don’t have to work as hard, and they last longer.
If you are ready to upgrade your security, give us a call at (940) 394-8744. I answer the phone personally, 24/7. Whether you need a simple keypad or a full video-intercom retrofit, we will give you an honest price and stand behind the work with our 90-Day Done Right Promise.
FAQs - Gate Access Control Cost
Can I install a smart gate opener myself to save money?
While you can buy DIY kits online, I strongly advise against it if your gate uses high-tension springs or heavy-duty industrial operators. These systems are under immense pressure and use high-voltage electrical connections; improper wiring can fry your main control board or cause the gate to crush an object or person. A professional install ensures the safety sensors are calibrated correctly-which is the most important part of the job. Call (940) 394-8744 if you want it done safely the first time.
How much does it cost to fix a gate keypad that isn’t working?
Most keypad repairs or replacements in Denton cost between $350 and $600, depending on whether the issue is a loose wire, a corroded battery terminal, or a failed circuit board. If the keypad has simply reached the end of its life, we can replace it with a compatible model that works with your existing gate motor. We offer free estimates, so call us before you decide to replace the entire system.
Is it cheaper to repair or replace my existing gate access system?
In most cases, it is significantly cheaper to repair or upgrade your existing system than to rip it out and start over. If your gate motor is less than 10 years old and the frame is solid, we can usually integrate modern access control for a fraction of the cost of a full install. We are a repair-first company, meaning we won’t try to sell you a new motor if yours just needs a new logic board or keypad.
Do you charge for a service call if you come out to look at my gate?
We do not charge a trip fee for service calls inside the county. If you are in the Denton area and need help with your gate access control, we will come out, assess the situation, and provide an upfront price. If you want a second opinion on a quote you already received from another company, that is also free.
How long does it take to install a new access control system?
A standard keypad or remote receiver installation usually takes about 2 to 4 hours, assuming the wiring is straightforward. More complex systems, such as cellular intercoms or multiple-gate integrations, can take a full day. We always prioritize getting your gate back to a secure, working state as quickly as possible. Call (940) 394-8744 to schedule a time that works for you.
Pricing reflects the Denton market as of 2026. Gatewood Fence & Gate offers free estimates - call (940) 394-8744.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Denton since 2001.
What Our Customers Say
"Driveway gate had been dragging for two years and two other companies told me the whole thing needed replacing. Hal reset the posts, rehung it and it swings like it did when it went in. A fraction of the price of a new one."
- Hollis Amberly"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth